Skip to content

Crushing Plant Carbon Footprint and Emission Reduction

Published: · Updated:
Crushing Plant Carbon Footprint and Emission Reduction

Which two numbers crushing plant carbon footprint and emission reduction rest on

A plant's carbon declaration does not come out of a complex model but out of two simple numbers: the energy spent on every tonne you produce and the emission factor of that energy. Work on crushing plant carbon footprint and emission reduction therefore starts with measurement, not with estimation. Put weighbridge data next to fuel and electricity consumption for the same period and you obtain litres per tonne and kilowatt-hours per tonne. Without those two figures no reduction target is verifiable, because a reduction claim only exists against a measured baseline.

The scope split: where each consumption is reported

For a declaration to be accepted, consumption has to be reported in the right scope. Fuel burned on site is a direct emission. Purchased electricity is reported separately as an indirect emission. Emissions created while the fuel is extracted, refined and delivered to the site are calculated with a separate upstream factor in the supply chain scope. That split matters, because a plant moving from diesel to electricity lowers its own direct emissions while total emissions fall only as far as the carbon intensity of the grid allows.

ActivityData to measureUnitWhere it comes fromReporting scope
Crusher and screen drives (electric)Electricity used in the periodkWhMeter, automation logPurchased energy
Operation on a generatorFuel delivered to the generatorlitresFuel tank recordsDirect combustion
Diesel-driven mobile plantFuel per unitlitresSite fuel docketsDirect combustion
Loaders and trucks (on site)Fuel per machinelitresFuel management systemDirect combustion
Product deliveryTonne-kilometrest·kmDelivery notesSupply chain
Production and delivery of fuelSame fuel quantitylitresFuel recordsSupply chain

Where the emission factor comes from

Factors are not invented; they are taken from the official conversion tables published annually for each country, and the table used must belong to the year being reported. For diesel a value of roughly 2.6 to 2.7 kilograms of carbon dioxide equivalent per litre is in widespread use, although the exact figure depends on fuel composition and on the edition of the table. For electricity there is no single global value: grid carbon intensity differs greatly between countries and shifts within a year. The declaration therefore names the table and the edition used; without that note, the number cannot be audited.

Setting the calculation up

The calculation is built in three lines. Line one is energy: litres and kilowatt-hours consumed in the period. Line two is production: saleable tonnes across the weighbridge in the same period. Line three is factors: the official factor chosen for each energy type. Multiply and add those lines and you get total emissions for the period; divide by tonnage and you get emission intensity per tonne. Per-tonne intensity is the only indicator suitable for target setting, because it stays comparable when capacity changes. Since the operating cost calculation feeds on the same two inputs, once energy recording is set up properly both cost and emissions are reported from one source.

Order of reduction: kilowatt-hours per tonne first

The cheapest route to lower emissions is not changing the energy source but spending less energy. The order runs as follows. First, stop crushing more than the specification asks for: producing finer than required consumes both energy and wear parts. Second, scalp: screening out fines that never needed to enter the crusher cuts wasted energy directly. Third, hold a steady chamber level, because a crusher fed in surges loses average efficiency. Fourth, deal with idling: a conveyor turning empty or a crusher running without feed keeps consuming while producing no tonnes. Fifth, look at internal haulage, where replacing a long truck route with a conveyor visibly lowers fuel per tonne.

Electric or diesel: the grid decides

Electric drive removes direct emissions from the site and produces no exhaust at the plant boundary. Total emissions, however, depend on how that electricity was generated: on a carbon-intensive grid the gain stays limited. Electricity produced on site by a generator adds conversion losses on top of diesel consumption, which is why a generator is not planned as a permanent solution where a grid connection is feasible. Three figures are compared in the decision: the grid factor, the cost of bringing power to the site and the plant's annual running hours. On an installation that works few hours the grid investment does not return, while on a continuously running fixed plant the gain appears on both the cost and the emissions side.

What recycling changes, and how the declaration is used

Processing demolition concrete close to the point of use is among the strongest levers on per-tonne emissions, because it removes both natural aggregate production and long-distance haulage. That gain only appears in a declaration if it is measured: the quantity of waste processed, the natural aggregate it replaced and the haulage distance avoided are all recorded. The declaration itself is tied to a document. Tender files usually ask for the same information: emission intensity per tonne, the source and year of the factors used, the scope split and the measurement period. With those four headings ready, a declaration is updated for each tender rather than rebuilt from nothing.

Definitions of technical terms: Glossary

Related Content

F80 P80 Reduction Ratio Calculation
MINING ENGINEERING

F80 P80 Reduction Ratio Calculation

Reduction ratio is the feed aperture passing 80 percent of the material divided by the product aperture passing 80 percent. Each ma…

Crushing and screening plant flowsheet design, worked backwards from the product
MINING ENGINEERING

Crushing and screening plant flowsheet design, worked backwards from the product

A flowsheet is not a parts list but a chain of decisions derived from the target product. Total reduction dictates how many stages …

How to Increase Cubical Product in a Mobile Crushing and Screening Plant
PLANT EFFICIENCY

How to Increase Cubical Product in a Mobile Crushing and Screening Plant

Cubical share rises not from one magic setting but from tuning feed size, reduction per stage, crusher type, rotor speed and the sc…

Cone or VSI? Cubic Aggregate in a 120-180 TPH Crushing and Screening Plant
PLANT EFFICIENCY

Cone or VSI? Cubic Aggregate in a 120-180 TPH Crushing and Screening Plant

In a 120-180 TPH plant, a correctly fed cone crusher usually meets the cubic requirement for 5-19 mm chippings, while manufactured …